• De afgelopen dagen zijn er meerdere fora waarop bestaande accounts worden overgenomen door spammers. De gebruikersnamen en wachtwoorden zijn via een hack of een lek via andere sites buitgemaakt. Via have i been pwned? kan je controleren of jouw gegeven ook zijn buitgemaakt. Wijzig bij twijfel jouw wachtwoord of schakel de twee-staps-verificatie in.

Raid schijf onzichtbaar bij xp installatie

Status
Niet open voor verdere reacties.
I

Incredyboy

Gast
Ik heb twee 80GB Sata schijven gekocht en geplaatst. Vervolgens in het bios als raid 1 (mirror) ingesteld. Vervolgens wil ik xp gaan installeren, maar als hij vraagt op welke partitie hij xp moet installeren is de lijst met schijven leeg.

Ik heb de raid-drivers vanaf mijn mobo-cd al op een diskette gezet, om vervolgens d.m.v. F6 deze aan de installatie toe te voegen, krijg ik de melding dat deze niet geladen kunnen worden met een foutcode 4.
Als ik dan op een willekeurige toets druk krijg ik het bleu screen of death van windows

Wat kan ik nu nog? De bestanden staan op de diskette, dus dat is het probleem niet. Het diskettestation werkt ook. Dit is een groot raadsel. Wie kan me helpen?
 
Dus als ik het goed begrijp kun je volgens dat artikel onder xp geen mirror raid gebruiken. Wel via een externe computer. Zouden er dan geen andere mogelijkheden zijn via een hulpprogramma of patch. Weet iemand hier iets over?
 
Hello again, wat voor moederbord heb jij; ik gaf eerder in Google het volgende in Raid 0 and XP installation en vond ik ook een PDF document, dat beschrijft hoe je via de Intel(R) Matrix Storage Technology XP installaleert. Als jouw moederbord dit ondersteunt, denk ik dat je met onderstaande geholpen bent. Succes.

Intel(R) Matrix Storage Technology
Quick Start Guide February 2005, Rev 1.0
Purpose
Provide the necessary steps to build a system using Intel(R) Matrix Storage Technology with one of two
configurations.
Setting Up a RAID 0/1/5/10 System
The following steps outline how to build a RAID system with Microsoft* Windows* XP installed on a RAID volume
using two, three or four SATA hard drives.
1. Assemble the system using a motherboard that supports Intel(R) Matrix Storage Technology and attach
SATA hard drives depending on the RAID level that will be built.
2. Enter System BIOS Setup; ensure that Intel Matrix Storage Technology is enabled. This setting may be
different for each motherboard manufacturer. Consult the user manual if necessary. When done, exit Setup.
3. Upon re-boot you will see the Intel Matrix Storage Manager option ROM status message on the screen
press CTRL-I to enter the Intel(R) Matrix Storage Manager option ROM user interface. Within this UI select
option #1 Create RAID Volume. Enter a volume name, press enter, use the arrow keys to select the RAID
level RAID 0, RAID 1, RAID 5 or RAID 10, press enter, select the drives to be used in the RAID array (unless
the system contains the minimum number of drives necessary for the selected RAID level), select the strip
size (only for RAID 0, 5, 10), press enter, enter the size of the volume (default is the maximum size, you can
make it smaller if you would like to create a second volume on the array later), press enter again, then press
Y to confirm. Once this is done, exit the option ROM user interface.
4. Begin Windows XP Setup by booting from the installation CD.
5. At the beginning of Windows XP Setup, press F6 to install a third-party SCSI or RAID driver. When
prompted, insert a floppy disk containing the Intel RAID driver. After reading the floppy disk, the Intel(R)
82801GR/GH SATA RAID/AHCI Controller (ICH7R/DH) will be presented -- select this driver to install.
6. Finish the Windows XP installation and install all necessary drivers.
7. Install the Intel Matrix Storage Manager software via the CD-ROM included with your motherboard or after
downloading it from the Internet. This will add the Intel(R) Matrix Storage Console which can be used to
manage the RAID configuration.
Setting Up a RAID Ready System
The following steps outline how to build an Intel RAID Ready system with Windows XP installed on a single
SATA hard drive.
1. Assemble the system using a motherboard that supports Intel Matrix Storage Technology and attach a single
SATA hard drive.
2. Enter System BIOS Setup; ensure that Intel Matrix Storage Technology is enabled. This setting may be
different for each motherboard manufacturer. Consult the user manual if necessary. When done, exit Setup.
3. Begin Windows XP Setup by booting from the installation CD.
4. At the beginning of Windows XP Setup, press F6 to install a third-party SCSI or RAID driver. When
prompted, insert a floppy disk containing the Intel RAID driver. After reading the floppy disk, the Intel(R)
82801GR/GH SATA RAID/AHCI Controller (ICH7R/DH) will be presented -- select this driver to install.
5. Finish the Windows XP installation and install all necessary drivers.
6. Install the Intel(R) Matrix Storage Manager software via the CD-ROM included with your motherboard or
after downloading it from the Internet. This will add the Intel(R) Matrix Storage Console which can be used to
manage the RAID configuration.
Post Migration Note: After migrating from RAID Ready to RAID 0, 1, 5, or 10 volumes, the RAID 0,1,5,10
Volume will have the combined capacity of all the SATA hard drives, but the migrated partition size will be
unchanged. This leaves unformatted space at the end of the RAID Volume. To use this space, use Windows XP
Disk Management to create another partition in the remaining empty space in the RAID Volume or use a thirdparty
application to expand the migrated partition to span the entire RAID Volume.
 
Dat hele verhaal is nogal vaag...

Simpel gezegt, het enige wat je eigenlijk moet doen is
4. At the beginning of Windows XP Setup, press F6 to install a third-party SCSI or RAID driver. When prompted, insert a floppy disk containing the Intel RAID driver.

Omdat RAID een apart systeem is, moet je eerst de driver van je raid controller in de windows xp setup stoppen, anders kan hij het niet vinden..
Dat is voor zo ver ik weet bij elk raid systeem zo...
 
Abraham54 zei:
Hello again, wat voor moederbord heb jij; ik gaf eerder in Google het volgende in Raid 0 and XP installation
Raid mirror werkt niet onder Raid 0 maar onder Raid 1. Maar ik zal eens kijken via google met deze zoekopdracht...

RonSijm zei:
Simpel gezegt, het enige wat je eigenlijk moet doen is
4. At the beginning of Windows XP Setup, press F6 to install a third-party SCSI or RAID driver. When prompted, insert a floppy disk containing the Intel RAID driver.
Dat had ik ook gedaan zie de eerste post in in dit topic.....
 
Hallo, als jij in Google Raid 0 and XP installation , krijg je een hoop info.
Ook bijv. het integreren van de Raid-drivers in de de Windows setup.
Succes.
 
Status
Niet open voor verdere reacties.
Steun Ons

Nieuwste berichten

Terug
Bovenaan